How to Pour Concrete Patio DIY | Pouring a Concrete Patio Cost
How to pour concrete patio? In this article we are presenting the guide or manual about how to pour concrete patio. Pouring concrete patio is actually not a big deal. We can do this work all by ourselves. The most important thing for pouring concrete patio is that you have to be prepared before working on it.
How to Pour Concrete Patio
Below are the instruction details in how to build a concrete patio slab.
Tools and Materials
Concrete finishing tools.
QUIKRETE® Acrylic Cure & Seal .
QUIKRETE® All-Purpose Gravel .
QUIKRETE® Concrete Mix or QUIKRETE® Crack-Resistant Concrete Mix .
Vegetable oil or release agent.
Pouring Concrete Patio Step by Step
Step 1 – Creating the Layout
Utilizing either garden hose or rope, create a rough outline for the designed concrete patio. After that, drive in stakes in alignment with, but placed approximately one foot outside, each corner of the rough concrete patio layout. Run mason’s strings between two stakes; if it is possible, try to get the two stakes set back approximately one foot from each corner so that the running mason’s strings will intersect at the designed corners of the concrete patio area. After that, it is time to square the staked-out area. Utilize a line level to make sure that the tied mason’s strings run at a correct level.
Step 2 – Excavating the Area
To save water from pooling on the concrete patio surface, you must give your concrete patio a kind of slight, rain-shedding slope. At this phase, making a set of the slope means creating angle of the the mason’s strings. Follow the directed two strings running away from the main building to the driven stakes where they are tied. Because the common slope is 1/8 inch per foot, you can multiply the designed length of the patio’s side (in feet) by 1/8. Whatever you get, that is how far down to move the mason’s strings.
After this, the most tiring part of the construction begins now. The idea is to excavate the project area—and six inches near it—to a depth of six inches below the mason’s strings. For all but the most forgiving soil, a square-end spade can be your best choice. Upon finishing the designed excavation, you can add in a layer of QUIKRETE® All-Purpose Gravel to give a specific level, stable foundation. Pour the gravel to a thickness of approximately five inches, then utilize a tamper to compress it to four inches.
Step 3 – Constructing the Formwork
While it takes quite good brawn to finish the site excavation, it takes quite nice finesse to built the form—that is, the wooden frame that wants to be constructed to receive the poured concrete, build its concrete patio thickness, and decide its shape. Start by positioning 2×4 boards onto the gravel along the edge of the designed concrete patio, utilizing the mason’s strings as a kind of benchmark. Because the inside dimensions of the form must similar to the total size of the designed concrete patio, set the wooden boards so that their inside perimeters hit nicely below the strings. After that, for each 3 feet along the outside perimeters of the form boards, drive in a foot-long stake cut from your stock of 2×4’s. To fasten the driven stakes to the wooden boards, drill three-inch deck screws through the one and into the other. Finally, after leveling the form boards, screw them all together to complete. To avoid the concrete to be sticky with the wood, coat the inside form boards with either a commercial release agent or vegetable oil.
Step 4 – Pouring Concrete Patio
Now you can continue to mix and pour the concrete in evenly placed mounds. After that, pour the concrete into the designed concrete patio location by means of a hoe. Then make the concrete patio leveled with a screed board—here, simply a 2×4. Make the screed smoother in a sawing motion, take away the excess concrete in front of the board and take it for filling any dips behind it. After the poured concrete has lost its shine, go over it with a wood float, do it with arcing motions to smooth the concrete patio surface. Then, complete the concrete pouring with a stiff-bristled broom to create the nonslip surface.
For this last step, prepare for seasonal contraction and expansion by utilizing a straightedge and groover to put in control joints. Control joints must be cut to a quarter of the slab depth and added at least every 10 feet in each direction. Finally, apply QUIKRETE® Acrylic Concrete Cure & Seal, this is to prevent stains and repel water. With this material, you do not need concrete curing.
If you are interested in video tutorial, QUIKRETE® provides you a good how to pour concrete patio youtube video so that you can work on the diy concrete patio pavers :
Pouring a Concrete Patio Cost
The pouring a concrete patio cost has been calculated by howmuch.net. In the following table the Labor Cost figure is what the able and prepared DIY persons should expect to save by performing the corresponding tasks.
Patio slab: 500 sq.ft.; include costs for miscellaneous material, equipment, and waste. The diy concrete patio cost will be as follows.
|Item||Unit Cost||Quantity||Line Cost|
|Concrete slab: excavate, prepare, pour, and broom finish 500 sq.ft. of 2″ thick concrete patio slab with rebar, wire mesh, and aggregate/sand base.||$2.17||per sq.ft.||525||$1,141|
|Upgrade: add earth tone color and pavers-embossing.||$0.45||per sq.ft.||525||$234|
|Material Cost||$2.75||per sq.ft.||500||$1,375|
|+ Labor Cost (base)||$36||per hour||24||$864|
|+ Labor Cost (upgrade)||$36||per hour||10||$360|
|Total Cost||$5.20||per sq.ft.||500||$2,599|
The cost above can change as time goes by.
Can you get the idea of how to pour concrete patio which is written above? The idea of how to build a concrete patio step by step instruction above is quite nice if you can follow. I am sure that now you understand how to pour a concrete patio against a house. We hope that this article is useful enough to help you to pour your concrete patio. If you think that this can be useful for others, please share. Thanks for visiting this website. You might also like these following articles: